Looking for:
ABB ACS USER MANUAL Pdf Download | ManualsLib.ABB ACS USER MANUAL Pdf Download | ManualsLib |
ACS Micro Drives - ACS Drives
Table Abb acs150 manual download Contents. Quick Links. See also: User Manual. ACS Drives 0. Table of Contents. Previous Page. Next Page. Speed control of majual to 50 hp 2. All Scs150 Reserved. Page 5: Safety Safety What this chapter contains The chapter contains the safety instructions which you must follow when installing, operating and servicing the drive. If ignored, physical injury or death may follow, or damage may occur to the drive, motor or ссылка на страницу equipment.
Read the safety instructions before you work on the drive. Never attempt to repair a malfunctioning drive; manuql your local ABB representative or Authorized Service Abb acs150 manual download for replacement. Page 8 ABB Standard macro Page 10 Efficiency Page About The Manual It contains a flowchart of steps for checking the delivery and installing and commissioning the drive. Compatibility The manual is compatible with the ACS drive firmware version 1. Technical data: Ratings on mwnual Plan the installation: select the cables, etc.
Planning electrical installation on page Check the ambient conditions, ratings and required Technical data on page cooling air flow. Page Hardware Description The chapter describes the construction and type code information abb acs150 manual download short. The construction of frame sizes R0…R2 varies to some extent.
Page Type Code Sketchup pro 2019.2 release notes free download type code contains information on the specifications and configuration of the drive. You find the type code on the type designation label attached to the drive. The explanations of the type code selections are described below. Page 16 Hardware description Page Mechanical Installation Mechanical installation What this chapter windows 10 1903 free download The chapter describes the mechanical installation procedure of the drive.
Check the enclosure requirements for the need to use the NEMA manusl option in wall installations see chapter Technical data. Dowhload Mounting The Drive Free space around abb acs150 manual download drive The required free по этой ссылке for cooling above and below the drive is 75 mm 3 in.
No free space abb acs150 manual download required перейти на страницу the sides of the drive, so they can be mounted side by side.
Mounting the drive Mount the drive Note: Make sure that dust from drilling does not enter the drive during the Page 20 Fasten clamping plates afs150. Fasten the clamping plate to the plate manuwl the bottom of the drive with the provided screws.
Mechanical installation Page Planning Abb acs150 manual download Installation Note: The installation must always be designed and made according to applicable local laws and regulations. Fuses must be used with other circuit breakers. Contact your local ABB representative for approved breaker types and supply network characteristics. /2839.txt Selecting The Power Cables Selecting the power cables General rules Dimension the input power and motor cables according to local regulations.
See chapter Technical data for the rated currents. Page 24 Motor cable shield To function as a protective conductor, the shield must have the same cross-sectional area as the phase conductors when they are made of the same metal.
The requirements are easily met abb acs150 manual download a copper or aluminium shield. For ACSx drives, other measures for protection in case of direct or indirect contact, such as separation from the environment by double or reinforced insulation or isolation from the supply system by a transformer, can also be applied. Relay cable The manuql type with braided metallic screen e. Routing the cables Route the motor cable away from other cable routes.
Motor /38578.txt of several drives can be run in parallel installed next to each other. Page 27 A diagram of the cable routing is shown below. Motor cable Drive min. Page 28 Planning electrical acs1150 Page Electrical Installation Electrical installation What this chapter contains The chapter describes the electrical installation procedure of the drive. The work described in this chapter may only be carried out by a qualified electrician.
Follow the instructions in chapter Safety on page 5. Ignoring the safety instructions can cause injury or death. Motor Ground the other end of the PE conductor at the distribution board. Use a separate grounding cable if the conductivity of the cable shield is insufficient smaller than the conductivity of the phase conductor and there is no symmetrically constructed grounding conductor in the cable see section Selecting the Page 31 1.
Page 33 Procedure 1. Analog signal if connected : Strip the outer insulation of the analog signal cable degrees and ground the bare shield under the clamp. Connect the conductors to the appropriate terminals. Connect the grounding abb acs150 manual download of the used pair in abb acs150 manual download analog signal cable to the SCR terminal.
Page 34 Electrical installation Page Installation Checklist Installation checklist Checklist Check the mechanical and electrical installation of the drive before start-up. Go through the checklist below together with another person. Read chapter Safety the first pages of this manual before you work on the drive.
Вот ссылка 36 Installation checklist The general parameter setting procedure in the Short Parameter mode down,oad described below. You find more detailed instructions on setting parameters on page Page 38 7. Save the downloaad value by pressing Enter the motor data from the motor nameplate: Note: Mqnual the motor подробнее на этой странице to exactly the same value as on the motor nameplate.
Page 39 Set constant speeds drive output frequencies 1, 2 and 3 parametersand Set the maximum limit for the drive output frequency parameter Check that there are no faults or alarms shown in the display. The drive is now downolad for use. Ensure that the drive is in remote control. Press key to switch In remote control, the panel display shows text REM. Page Control Panel The chapter describes the control panel keys and display fields. It also downllad in using the panel abb acs150 manual download control, monitoring and changing the settings.
Control panel Page 44 Overview The ab table summarizes the по этому сообщению functions and displays on the Integrated Control Panel. Use LCD display — Больше на странице into five areas: a.
Cownload 45 The ACS includes an integrated potentiometer located at the front of the drive. It downlpad used for setting the frequency reference. Page 46 How to do common ac150 The table below mmanual common tasks, the mode in which you can perform them and the page number where the steps to do the task are described in detail.
Приведенная ссылка Mode Page How to switch between local and remote control How to start and stop the drive How to change the direction of abb acs150 manual download motor rotation How to set the frequency reference Page 47 How abb acs150 manual download start, stop and switch between local and remote control You can start, stop and switch between local and remote control in any mode.
To be able to start or stop the drive, the drive must be in local control. Step Amnual Display Both function identically, except that the Abb acs150 manual download As150 mode shows only the minimum number of parameters typically required to set up the drive see section Parameters and abb acs150 manual download in the Short Parameter mode abb acs150 manual download page Axs150 52 Step Action Display Use keys to select the parameter value. When you have changed the parameter value, starts flashing.
Page 54 Control panel Page Application Macros Application macros are preprogrammed parameter sets. The ACS has five application macros. The table below contains abb acs150 manual download summary of the macros and describes suitable applications. Macro Suitable applications ABB Standard Ordinary speed control applications where no, one, two or three constant speeds are used.
Parameter values are the default values given in chapter Actual signals and parameters, starting ahb page If you use other than the default connections presented below, see section terminals on page Page abb acs150 manual download Macro 3-wire macro This macro is used when the drive is controlled using momentary push-buttons.
It provides three constant speeds. To enable the macro, set the value of parameter to 2 3-WIRE. For the parameter majual values, see abn Default values with different macros abb acs150 manual download page
No comments:
Post a Comment